Apex-Pro
Quick Sheet
Apex-Pro
ptsconfig utility
The PTSCONFIG
utility is a console application that allows you to configure the
Apex-Pro application. Instructions for access to the PTSCONFIG
utility are as follows:
Step 1 : Select
setup CIC button on the CIC display.
Step 2 : Select
the service password tab.
Step 3 : In
the password window type mms_com and click Apply.
An MSDOS command prompt window will appear.
Before proceeding
you MUST obtain the Mission Critical
IP address to the Apex-Pro application (e.g. 126.1.x.x
– the IP address label is on the top right hand side of the
CIC directly above the Apex-Pro network interface
card IP address of 119.1.1.2)
Step 4 : In
the MSDOS window type cd c:\program files\marquette\pts\x.x
(where x.x is the current revision of the Apex-Pro software,
e.g. 1.1) then press Enter.
Step 5 : When
the new directory prompt appears, type ptsconfig 126.x.x.x.
When the following appears:
Attempting to get connection port from 126.x.x.x
Connecting to 126.x.x.x on port xxxx
Connected…
Press Ctrl + ] to disconnect
ApexPro
Version 1.x Copyright GE Marquette Medical Systems, Inc., 2000.
All
rights reserved.
[126.x.x.x]
C:\Program Files\Marquette\PTS\1.x>
you are connected. You can use the following commands.
Typing help
at the prompt will list all of the following commands:
DISPLAY Commands:
These commands only display the Apex-Pro information.
Syntax: - display <space> tower <enter> |
| tower |
Apex-Pro tower's full name "UNIT|NAME |
| software |
Software versions for everything (main, rack, etc...) |
| build |
Date and Time the software was built |
| patient |
Patient information: TTX, Tower and Receiver numbers |
| patreceiver |
Information about the patient's receiver and transmitter |
| ip |
IP address used by the Apex-Pro application to talk to the
unity network |
| rack |
IP address used by the Apex-Pro application to talk to the
Rack network |
| receiver |
Receiver/Unit assignments for this Apex-Pro tower |
| ttx |
Network-wide in-use TTX list (from TTX Master) (includes CDT-LAN) |
| unitlist |
Network-wide unit/receiver list (from TTX Master) |
MODIFY COMMANDS:
These commands allow modification to the Apex-Pro setup.
Syntax: - modify<space> tower<enter> |
| unit |
Assigns the Apex-Pro a unit name (this is not a filter) |
| tower |
Assigns the Apex-Pro tower name |
| ip |
Assigns the IP address used by the Apex-Pro application to
talk to the unity network |
| rack |
Assigns the IP address used by the Apex-Pro application to
talk top the Rack network |
| receiver |
Assigns Receiver/Unit assignments for this Apex-Pro tower
(this is a filter, and will allow only assigned units to admit) |
OTHER COMMANDS: |
| admit |
Admits a patient to this Apex-Pro tower ("admit
shows usage) (syntax: admit <space><unit><space><name
or -><space><ttx#><space><age> |
| discharge |
Discharges a patient from this Apex-Pro tower ("discharge
shows usage) (syntax: discharge <unit|bed> |
| dload |
Download rack software ("dload shows usage) |
| resetrack |
Resets the receiver sub system immediately with no confirmation |
blink
- patient
- rack
- receiver
- stop |
Blink receiver sub system LED(s) according to:
- Entered patient name (unit|bed)
- Entered Apex-Pro application IP address
- Entered Apex-Pro application IP address and receiver number
- Stops any and all blinking (syntax: blink stop |
| boot |
Reboots the PC ("DDMM password & confirmation) |
| shutdown |
Restarts the Apex-Pro application ("DDMM password & confirmation) |
statistics
- waveform
- wavereset
- histogram
- histreset |
Displays Apex-Pro software performance statistics:
- Waveform data latency timing through Apex-Pro software
- Reset waveform data latency timing counters
- Waveform data timing through Apex-Pro software
- Reset waveform data timing counters |
| storeecg |
Store a file containing raw patient ECG sample data |
| 